BRK electronic FE10GR User Manual download pdf

User’s Manual

ry Chemical

ire Extinguisher

Models FE5GR,

E10GR, FE1A10GR

IMPORTANT! Please read carefully and save.

This user’s manual contains important information about your fire

xtinguisher’s operation. If you are installing this fire extinguisher for

use b

y others, you must leave this manual—or a copy of it—with the

end user.

Read e

xtinguisher label and the entire user’s manual carefully before

installing or using the unit. Make sure everyone in your household is

com

pletely familiar with the operation of the extinguisher, and review

the instructions regularly. In an emergency, you will not have time to

read instructions.

IMPORTANT INFORMATION ABOUT

FIRE EXTINGUISHERS

NOTE: Be sure the extinguisher is rated to fight the type of fire most

likely to occur in the area you choose to install it. Since household fires

commonly start in the kitchen, you should always install an extinguisher

in the kitchen. For added security, you should also install additional

extinguishers in utility areas, and other living areas in your household.

FE5GR is rated Class 5-B:C.

FE10GR

is rated Class 10-B:C.

FE1A10GR

is rated Class 1-A:10-B:C.

READ BEFORE INSTALLING OR USING

S F

IRE E

INGUISHER!

Fire extinguishers are classified by fire type. The A, B and C

rating system defines the kinds of burning materials each fire

extinguisher is designed to fight. The numbers in front of the

A, B, or C indicate the rating for size of the fire the unit can

extinguish. Using the wrong type of fire extinguisher can do

more harm than good. Make sure you understand which fire

extinguisher to use on each class of fire!

Class A rating:

The agent/powder is suitable for

fighting small fires involving wood, paper, cloth,

rubber, and some plastics.

Class B rating: The agent/powder is suitable for

fig

hting small fires involving grease, oil, gasoline,

kerosene, and other flammable liquids.

Class C rating: The agent/powder is suitable for

fighting small fires in "live" electrical equipment.

WHE

RE TO INSTALL THIS EXTINGUISHER

Fire Extinguisher Should Be Mounted:

•

In the vicinity of (but not on or in) a potential source of heat

and/or fi

re, like an oven or stove.

•

Where it is easy to reach, near an exit or an escape route

from the room.

•

In a location that is convenient, in plain sight, and 3-1/2 to 5

eet (1 to 1.5 meters) above the floor.

•

Store the extinguisher high enough to keep it out of the reach

of small children.

• On a clean, dry surface where the temperature does not go

ove 120° F (49° C) or below –40° F (–40° C).

HOW TO INSTALL THIS EXTINGUISHER

INSTALL THE MOUNTING

BRACKET ON A WALL

. The extinguisher has a bracket for

all mounting.

2. Install the mounting bracket on a

wooden stud or other solid surface

hat will support the weight of the

xtinguisher using the screws or

lts you purchased.

NOTE: Since wall surface types

vary, mounting screws are not

included.

Purchase screws or

bolts specifically designed for

the surface on which you will

mount the fire extinguisher. The

fire extinguisher label lists its

maximum weight. Mounting screw

head type should be #8 pan on

round head screws with #8 flat

washers.

3. After installing the mounting

bracket, replace the extinguisher

on the bracket with the label facing

outward, so the label can be easily

read. Wrap the bracket strap around

the cylinder and snap the buckle

closed.

INSTALLING THE MOUNTING BRACKET IN A

MARINE CRAFT

According to the NFPA Standard 302 (Fire protection Standard for

Pleasure and Commercial Motor Craft):

• On marine craft, portable fire extinguishers shall be located to be

readily accessible. Extinguishers shall be secured with a marine

bracket to permit immediate release.

• On marine craft, extinguisher agent cylinders shall be mounted a

minimum of 2 inches (5 cm) above moist or wet surfaces to reduce

he d

nger of corrosion.

CHECKING AND INSPECTING THE

FIRE EXTINGUISHER

1. Inspect the extinguisher once a week. Remove the extinguisher

from the mounting bracket and inspect the gauge. If the yellow

r is i

n t

he GREEN area, the extinguisher is properly pressur-

ized and ready to use.

If the pointer drops into the RED area,

the extinguisher has lost some pressure and should be

repl

ced

2. Check for signs of damage or misuse. Make sure you can still

ead all the text on the label. Carefully examine the surface of

the extinguisher for corrosion. You can help prevent corrosion

y clea

ning the extinguisher if it gets wet or dirty. If you notice

corrosion during the warranty period, return the unit to First Alert

(see "Limited Warranty" at the end of this manual).

e sur

e t

he t

amper indicator ("safety seal") is still intact and the

nozzle is clean and unobstructed.

n y

ou fi

nish inspecting the extinguisher, always put it back

securely into the mounting bracket.

For more information about fire extinguishers, consult the NFPA

ndard #10, "Portable Fire Extinguishers," available from the National

Fire Protection Association, Inc., Batterymarch Park, Quincy, MA 02169,

SA.

•

Do not mount the extinguisher on drywall or plaster without

adeq

uate support. Use strong screws or bolts to mount the

bracket securely into solid wood or metal that can support

, like a wooden partition stud. Secure mounting is needed

o you can remove the extinguisher quickly and easily in an

emergency. Also, if the extinguisher is not held securely, it

could dr

op to the floor and injure people or damage the

xtinguisher.

•

DO NOT BREAK THE SAFETY SEAL! This seal prevents

ccidental discharge of the fire extinguisher. Break the seal

only in an emergency before using the fire extinguisher.

W TO OPERATE YOUR FIRE

EXTINGUISHER IN A FIRE EMERGENCY

TO FIGHT THE FIRE

1. Remove the extinguisher from the mounting bracket.

2. Hold the unit firmly with the nozzle facing away from you. Pull out

the pin to break the “Safety Seal”. You won’t be able to squeeze

the lever until the safety seal is removed.

3. Stand back 6 feet (2 meters) from the fire and make sure the fire is

not between you and your exit.

4. Hold the extinguisher upright and aim the nozzle at the base

of the fire.

5. Squeeze and hold the lever to discharge the powder.

Sweep the spray at the base of the burning material, using quick

side-to-side motions. (If the spray scatters the fire, move back.)

7. Move slowly towards the fire as the extinguisher spray pushes the

fir

e b

ack. Maintain a 6-foot (2 meter) distance between you and

he f

ont of the fire at all times.

8. Completely discharge the contents of the extinguisher and make

sur

e t

he fir

e is com

tely out. Flashbacks are common with fires.

9. For kitchen fires on a kitchen stove, turn off the stove immediately

if possible, otherwise as soon as it is safe.

10. If you suspect a fire had an electrical origin, shut off the electrical

power, if possible, without eliminating your escape route. Do not

touch electrical wires or appliances.

11. After you have completely discharged your extinguisher, leave the

building and close all the doors behind you.

AFTER THE FIRE IS EXTINGUISHED

Do not turn the electrical power back on or plug in any appliances

l the area has been cleaned up comple

tely

It is very important

to remove the powder from electrical equipment after a fire. If the

powder gets wet, it can conduct electricity. (Using a dry chemical

xtinguisher on wet electrical equipment may be hazardous for this

reason.) This may worsen an electrical leakage problem, impair the

pment’s insulation, or create an electrical shock hazard.

If the fire was on a kitchen stove:

• Make sure the oven and all burners are turned off.

• Clean up the powder completely before using the stove or oven.

“

w t

o Clean After Using a Fire Extinguisher”. Ventilate the

area thoroughly.

If y

ou thi

k the fi

re had an electrical origin:

•

ut o

f t

he electrical power, if possible--do not touch any

electrical wires or appliances.

• Leave the building and close all doors behind you. Call the Fire

Department and have them inspect the premises. As soon as they

y it’s safe to return, ventilate the area thoroughly.

• Have a licensed electrician inspect your electrical system. Do not

turn the power back on or plug in any electrical equipment until

he i

nspe

ction has been completed.

•

Make sure your extinguisher may be safely and effectively

used on the small fire you want to fight. Always use extreme

cauti

on when fighting any fire. Fight a fire only where there is

a clear escape p

ath to allow you to get out safely if the fire

gets worse.

• Avoid breathing smoke and heated fumes; stay low if

necessary. Burning materials will release toxic fumes.

nhaling these fumes may cause injury or death.

•

Always stand back far enough away from the fire—near an

exit—and make sure nothing is between you and your

escape route. If you get too close to a fire, you risk getting

burned or hit b

y splattering material like grease. If the fire is

too hot or smoky for you to get within 6 feet (2 meters), DO

NOT try to fight the fire yourself. Evacuate immediately and

ll the Fire Department.

•

For fires on a kitchen stove, turn oven or burners off

mmediately if possible. If you can’t reach the oven or burner

controls safely, extinguish the fire first, then turn them off.

•

Fight the fire from an upwind direction with your back to any

strong air current. Trying to fight a fire with currents blowing

owards you can result in serious injury.

W TO CLEAN AFTER USING A FIRE

EXTINGUISHER

OTE:

he powder spray from the extinguisher may spread over a

ide area, and may soil upholstery, carpets and walls.

•

Sweep/vacuum up as much of the powder as possible. Then use

a d

amp cloth to wipe off the remaining agent.

• If you have any questions about cleaning appliances that the

agent has come into contact with, please contact the appliance

nufacturer.

IF YOUR EXTINGUISHER NEEDS SERVICE

his fire extinguisher is rechargeable by a certified fire equipment

dealer, regardless of how much of the content was used.

nce a year, a certified fire equipment dealer, in accordance with the

rvice manual identified on the fire extinguisher label, should service

the fire extinguisher. Please refer to your local telephone directory for a

rtified dealer.

o not try to service or repair this fire extinguisher under any

rcumstances. Do not try to remove the nozzle or valve assembly.

This is a pressurized device that can cause serious injury if

tampered w

ith.

f there is a problem and it is still under warranty, please see “How to

Obtain Warranty Service” in the Limited Warranty.

DISPOSING OF A USED EXTINGUISHER

If you choose not to have a used extinguisher refilled or a non-working

nit repaired, take it outdoors, turn it upside down, and discharge it

completely. Dispose of the empty unit properly, and replace it with a

new fire extinguisher.

Never puncture, burn or expose this fire extinguisher to tempera-

tures o

ver 150° F (66° C) even if it is fully discharged. The contents

are under pressure and it could explode.

LIMITED WARRANTY

BRK Brands, Inc. ("BRK") the maker of First Alert

brand products,

arrants that for a period of ten years from the date of purchase, this

product will be free from defects in material and workmanship.

BRK, at its option, will repair or replace this product or any component

of the product found to be defective during the warranty period.

Replace

ment will be made with a new or remanufactured product or

component. If the product is no longer available, replacement may be

made with a simi

lar product of equal or greater value. This is your

exclusive warranty.

This warranty is valid for the original retail purchaser from the date of

initial retail purchase and is not transferable. Keep the original sales

receipt. Proof of purchase is required to obtain warranty performance.

BRK dealers, service centers, or retail stores selling BRK products do

not have the right to alter, modify or any way change the terms and

conditions of this warranty.

This warranty does not cover normal wear of parts or damage result-

ing from any of the following: negligent use or misuse of the product,

use on improper voltage or current, use contrary to the operating

instructions, disassembly, repair or alteration by anyone other than

BRK or an authorized service center. Further, the warranty does not

cover acts of God, such as fire, flood, hurricanes and tornadoes.

BRK shall not be liable for any incidental or consequential damages

caused by the breach of any express or implied warranty. Except

to the extent prohibited by applicable law, any implied warranty of

merchantability or fitness for a particular purpose is limited in duration

to the duration of the above warranty. Some states, provinces, or

jurisdictions do not allow the exclusion or limitation of incidental or

conse

l d

mages or limitations on how long an implied warranty

lasts, so the above limitations or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have

r rights that vary from state to state, or province to province.

w t

o Obtain Warranty Service:

vice:

f se

rvice is required, do not return the product to your

retailer. In order to obtain warranty service, contact the Consumer

Affairs Division at 1-800-323-9005, 7:30 AM to 5:00 PM, Central

Standard Time, Monday through Friday. To assist in serving you, please

have the model number and date of purchase available when calling.

Address: 25 Spur Drive, El Paso, TX 79906

Marine Type, U.S.C.G. Type B:C, Size I

U.S.C.G. Approval Number 162.028/EX3622

Valid only with Bracket Number P87-0340

or Bracket Number B70-0161 and Strap Number S70-0007.

Bracket included.

8-0

137-004

M 03/0

First Alert

is a registered trademark of the First Alert Trust.

1 2 3 4

007 BRK Brands, Inc., a Subsidiary of Jarden Corporation

3901 Liberty Street Road, Aurora, IL 60504-8122

Consumer Affairs: (800) 323-9005 • www.firstalert.com

hank you for choosing First Alert

or your fire extinguisher needs.

ou have purchased a high quality fire extinguisher designed to

protect you and your family in case of a fire danger.

8-0137-004

M 03/0

Remove Extinguisher

from Bracket

Break the

Safety Seal

queeze and Hold

Lever To Discharge

Powder. Sweep

ide to Side.

• This extinguisher is designed for use against small fires

tha

t ha

ve just started and are small enough to fight safely.

It is not designed to fight large fires that are burning out of

control. If the fire is too hot or smoky for you to get within

6 feet (2 meters) of it, do not try to fight it yourself. Warn

one, evacuate the premises, and have someone call the

ire Department from outside the building. Trying to fight a

large fire yourself can result in injury or death.

•

o n

t puncture or burn any fire extinguisher. The contents

are under pressure

, and the extinguisher could explode.

• Never locate this extinguisher close to an engine, stove or

ther s

our

ce o

f heat. It is pressurized and could rupture or

xplode if exposed to temperatures over 150° F (66° C).

•

his extinguisher contains a dry powder extinguishing agent.

The agent/powder is nontoxic, but can irritate skin. When using

this unit

void breathing the powder. Always ventilate the area

ter us

•

DO NOT CHECK THE PRESSURE OR TEST THE FIRE

EXTINGUISHER BY SQUEEZING THE LEVER, EVEN BRIEFLY.

ONCE USED, IT WILL GRADUALLY LOSE PRESSURE AND

WILL NOT BE FULLY CHARGED FOR USE IN AN EMERGENCY.

• When the pointer drops into the red area, the extinguisher

y s

l be pressuriz

but must be recharged.

own

ith plastic

bracket

own

ith metal

bracket

User’s Manual 1

Summary of Contents

Page 1 - User’s Manual

User’s ManualDry Chemical Fire ExtinguisherModels FE5GR,FE10GR, FE1A10GRIMPORTANT! Please read carefully and save.This user’s manual contains importan

Comments to this Manuals

No comments

BRK electronic FE10GR User Manual

Browse online or download User Manual for Unknown BRK electronic FE10GR. BRK electronic FE10GR User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown BRK electronic FE10GR